Zusammenfassung
In der Online-Zeitschrift für Forschung und Entwicklung in der Produktion – wt Werkstattstechnik online – werden die aktuellsten Forschungsergebnisse aus Wissenschaft, Technischer Hochschule und Industrie veröffentlicht - praxisbezogen und zukunftsorientiert. Die wt Werkstattstechnik online erscheint inklusive neun produktionsspezifischen Ausgaben pro Jahr unter der Internetadresse www.werkstattstechnik.de. Die in der wt Werkstattstechnik veröffentlichten Fachaufsätze sind wissenschaftlich-methodisch aufbereitet und grundsätzlich Erstveröffentlichungen. Viele Fachaufsätze sind peer-reviewed: von Experten auf diesem Gebiet – anonym sowie unabhängig von den Autoren – wissenschaftlich begutachtet und freigegeben. Die wt Werkstattstechnik online ist Organ der VDI-Gesellschaft Produktion und Logistik (GPL) sowie der wissenschaftlichen Gesellschaft für Produktionstechnik (WGP).
- 374–427 Titelthema Aufsatz 374–427
- 428–429 Titelthema Fraunhofer 428–429
- 430–468 Titelthema Aufsatz 430–468
10 Treffer gefunden
- „... . Nevertheless, a proper selection of parameters is necessary, which is described in this article. The ...” „... Jahrgang 106 (2016) H. 6 381 2 Auslegung der Parameter beim Schleifen mit elastischen ...” „... keramischen Schleifscheibe der Korngröße 120 mesh erzielt. Die dazu verwendeten Parameter sind der Tabelle ...”
- „... ebenfalls in diesem Kapitel thematisiert. Ebenso werden die verfügbaren Parameter des Generators betrachtet ...” „... ] Parameter Minimalwert Maximalwert Bemerkung Ton (on-time) 1 127 Pulsdauer in µs Toff (off-time) 1 1027 ...” „... der Pulsform „Potentiometer“ 1 10 Regelverstärkung Tabelle 2: Parameter des HSWEDM-Prozesses ...”
- „... zeitlichen Einflüssen. Damit ist die Prozesszeit ein exogen vorgegebener Parameter, welcher zur Definition ...” „... = C1 (x + B)b Der Parameter y gibt die durchschnittlich benötigte Zeit (oder Kosten) pro Einheit an ...” „... . Der Parameter x nennt die Anzahl an gefertigten Einheiten. B korrespondiert mit der vorhergehenden ...”
- „... in Abhängigkeit von einer geeig neten Messgröße. Allgemeine Parameter des Temperaturregelsystems ...” „... eingestellten Parameter, – kundenspezifische Datenablage, – Kommunikation mit Maschinen steuerungen über ...”
- „... Schleifprozesse ebenfalls übertragbar. Die Modelle sind häufig mathematisch mit freien Parametern formuliert. Die ...” „... Kalibrierung und Ermittlung der prozessspezifischen Parameter kann direkt im Prozess erfolgen oder sie wird in ...”
- „... technological investigations about the influence of machining parameters on edge rounding will be presented ...” „... Jahrgang 106 (2016) H. 6 401 parameter, die in drei Einflussgruppen zusammengefasst werden [5, 6, 9–11 ...” „... Verfahrensprinzip an der Wirkstelle Tabelle. Untersuchte Parameter Titelthema – Aufsatz Copyright ...”
- „... Fügestellen Die relevanten physikalischen Parameter der geklebten Füge stellen der Versuchswerkzeuge wurden ...”
- „... können. Eine Anpassung der Parameter für zukünftige Schleifversuche (ae, vfr, nw) kann anhand der hier ...”
- „... allerdings nur im getesteten Parameterraum Gültigkeit, was auch den verwendeten Werkstoff einschließt. Ein ...”
- „... Prüfverfahren, sowie einer Parameteroptimierung bei bereits ausgewählten Fertigungstechnologien erfolgen. 4 ...”