„… , are, for all intents and purposes, anisotropic [1]. Fiber orientation and distribution determine the …” „… computation of properties as a function of the fiber orientation distribution. Examples of the application of …” „… testing machine, equipped with a 150 kN load cell. Fig. 5: Four-point bending set-up Gate 1 …”

„… were applied on two sides of the upper horizontal profiles and loads were applied to different …” „… are examined, then pre-tension effects analyzed. Two different load cases were applied in the first …” „… more accurately. Fig. 10: Von-Mises stress results after a pre-tension load on the bolts 305 …”

„… , are, for all intents and purposes, anisotropic [1]. Fiber orientation and distribution determine the …” „… computation of properties as a function of the fiber orientation distribution. Examples of the application of …” „… testing machine, equipped with a 150 kN load cell. Fig. 5: Four-point bending set-up Gate 1 …”

„… friction induced between the particles causes a gradual load distribution into the particle core, which …” „… structures, load introduction zones and functional elements. Currently the combination of flat reinforcing …” „… additional metal load-introduction elements. With a view to securing a high stress-bearing capacity of the …”

„… were applied on two sides of the upper horizontal profiles and loads were applied to different …” „… are examined, then pre-tension effects analyzed. Two different load cases were applied in the first …” „… more accurately. Fig. 10: Von-Mises stress results after a pre-tension load on the bolts 289 …”

„… aerodynamic operating conditions demand a maximum load-bearing capacity of the components. In order to …” „… bodywork component of the 911 Carrera. 97 Fig. 5: Wall thickness distribution Further …” „… complete-vehicle tests, such as high load endurance, crash testing, corrosion testing and wind tunnel tests, must …”

„… Load-appropriate dimensioning is only conditionally possible Low flexibility in mat production. International …” „… to achieve an optimal distribution of the fiber. Once the mold was completely filled, a compression …”

„… to determine the stress distributions on the meshed structure. To accomplish this, a unit load case …” „… distribution is determined for each load case. The inertia relief method, in which the external load is …” „… component design in the form of load data for use already in very early phases of development. In order to …”

„… divided by the load carried by the tire. When the tire is rolling, it generates heat because it is made …” „… ), for a truck tire: - Speed = 80kph - Load = 85% of load index - 3 hours warm up phase - Ambient …” „… a bit different since: - The actual load on the tire differs from the 85% of load index that is …”

„… onboard vehicle load Position, load, pressure, … Air Spring, Shocks Date, localize and categorize …” „… ) compared to current parts • Intensive unidirectional Loads • No bending or torsion due to elastomer …” „… bearings or ball joint • All fibers are oriented in load direction • Bonding results in a very homogenous …”

„… and distribution markets, offering optimization potential. Quality is a prerequisite. It requires …” „… determined from load collectives, see literature | 3 |, for representative driving situations recorded with …” „… . 7: left: Recording of load spectra for demanding operating conditions, right: Vehicle test bench …”

„… electric drivetrain, DC/DC converters, power distribution units (PDU), the HV and LV cabling system …” „… the various consumers one or multiple power distribution units (PDU) are required. Splitting the …” „… efficiency map and full load characteristic of e-motors and inverter efficiency. The fuel cell VDI-Berichte …”

„… . Thereafter, a statistical model is derived to represent the variety of the observed parameter distribution …” „… is shown in Figure 3.1. The particles of interest are subjected to a uniaxial compression load in a …” „… cylinder up to a height of 181 mm. Two forces are measured. First, the Cylinder Load cell Granules …”

„… distribution of diameter, crushing strength, and Young’s modulus using material-dependent parameters. This …” „… leads to a combined three-dimensional distribution with a total of nine parameters describing a granular …” „… that the grains undergo crushing and fragmentation when subjected to loads beyond a threshold value …”

„… particle size distribution at different stress levels. The test is described in detail in DIN 18135, and a …” „… stress-strain curves are determined. Before examining the particle size distribution at different stress levels …” „… distribution 41 4 Determination of bulk particle properties of the void ratio in the specimen, while the change …”

„… changed load distribution. Thus, designs such as the X-Core or Y-Core [31], see Figure 1.2, between the …” „… . In particular, particle crushing under high load is a very complex mechanism. In the maritime sector …” „… distribute the local load occurring during a collision, and to dissipate energy. The feasibility of this idea …”

„… hull and load distribution contributes considerably to collision safety. Due to the support of the …” „… : Strain distribution of the inner hull in the simulation at the beginning of rupture. Inner hull Shape of …” „… , while in the simulations, it is the inner hull that carries a higher load. This could be caused by the …”

„… of scaled double hull structures under collision load in finite element simulations, Procedia …” „… , A. Levy, H. Kalman, S. Aman, J. Tomas, Strength distribution of particles under compression, Powder …” „… material parameter distribution of expanded granules, Granular Matter 19 (3) (2017) 52. doi:10.1007/s …”

„… modular benchmark for evaluating load distribution algorithms" ) [14] (H. Elfaham, C. Wagner, M …” „… . Anapolska, U. Epple, "Modeling and Investigating Load Distribution and Resource (Re-)Allocation for Next …” „… Deployment-Konzept durch die Distribution Logic, Optimizer und Boundary Condition Manager dargestellt. Das …”

„… . Third, the system load data of the entire system has to be given: the input of the planned production …” „… given. According to the definition of section 1, the system load data is considered open and dynamic …” „… interoperability, data distribution, extensibility of the data model, VDI-Berichte Nr. 2330, 2018 667 standardized …”

„… ] Elfahaam, H.A., et. al: Modeling and Ivestigating Load Distribution and Resource (Re-)Allocation for Next …”