„… Two-phase water evaporation MESHFREE CFD method for wet automotive component dry-out time …” „… newly developed mass transfer model extends its capabilities in these applications. The multi-phase …” „… the error bars marked in the exper-imental data show the error range based on the measurement …”

„… complement or replace physical prototypes with virtual prototypes. To identify errors in components and …” „… products frequently to quickly identify errors [3] in component and integration of software and plant …” „… behaviour over time to obtain or increase reliability. If errors and failures occur during the cycle new …”

„… process in both the training and predictive phase. By the introduction of weight-importance driven …” „… : ??? ?? ??? ?? ??? ?? , ? ?, … ,??, (6) Where ? ∈ ℝ and in which ? ? ∈ ℝ denotes the error over the joint space Ω Ω Ω that combines …” „… the uncertainty over the weights Ω and the modelling error Ω . Hence, argument ? denotes the …”

„… phase of cooling plates, several disciplines have to be tackled at once: Those are the simulation of …” „… that was able to predict unseen design with an error below 10 %. An exemplary prediction is shown in …” „… Absolute Prediction Error Temperature in K Temperature in K Fig. 10: Prediction of temperature field on …”

„… errors as key testing objectives [14]. During the development process of vehicles, the definition of the …” „… scenarios required during the development phases [10]The R2R test rig setup is an enhanced test rig XiL for …” „… emergency braking is performed. Acceleration to the specified speed and the braking phase are tested on the …”

„… zurückführen? Nachfolgend wird auf die Ansätze zur Lösung dieser Aufgabenstellungen in der Nutzungs-phase …” „… Untersuchungen liegt der Fokus auf der Nutzungsphase. Um die Fragen in diesen Phasen des Lebenszyklus zu …” „… getestet und erreichte einen mittleren MAPE (Mean Absolute Percentage Error) zwischen 1.19% und 3.12% pro …”

„… can be seen in table 2. The simulation was performed in 3 phases, starting with an initial steady …” „… phase with the same 0.5e-4s times step but the inner iteration reduced to 4 per time step which was then …” „… difference to experiment of 0.010 and 0.002 respectively, the latter representing less than 1% error …”

„… classification error of boosted classifiers on the test set. Hence, the basic idea of the following approach is …” „… classification confidences during training on the test error is subject to the margin theory that is briefly …” „… training. Roughly after 10 rounds, the training error reaches zero as all examples images have a positive …”

„… in an in general computational expensive and time-consuming learning phase. Figure 1.3 presents the …” „… its positive and negative part with a comparatively small error. (b) The learned detector is utilized …” „… set in its positive and negative part with a preferably small error. A positive training example for …”

„… phase of the AdaBoost algorithm (see Algorithm 3 and Equation (3.17)). Each weak classifier returns 0 or …” „… error of that weak classifier in training. Thus, the maximum positive classification of a strong …” „… τs = 12 ∑NRs r=1 αrs. AdaBoost’s decision threshold aims at a low error rate on the training set …”

„… phase. Dealing with tasks unrelated to driving – compared to Level 2 – should not lead to passive task …” „… “got tired” depending on the automated driving duration. Error bars represent the standard error …” „… area of the automated drive. One time area contains approx. eight minutes. Error bars represent the …”

„… , German Aerospace Center (DLR) - Institute of Vehicle Concepts Abstract The early design phase and …” „… the vehicle design phase, hence allowing researchers and engineers to create better and more …” „… any new vehicle development project is known as the early design phase [1]. In this period ideas and …”

„… the functionality of the unit under test at different development phases. Having such development …” „… parameter (Design variable) is varied one at a time in a “trial and error” approach until the tuning …” „… in an ECU might cause fatal error to the unit under test or safety critical situation. It is …”

„… Phasen des Lebenszyklus einer Produktionsanlage wichtig: In der ersten Phase „Design“ geht es um die …” „… Phase „Nutzung“ (operation) dient er einer besseren Verfügbarkeit der Maschinen und ermöglicht die …” „… im Millisekunden-Takt Die Inbetriebnahme einer Anlage gehört zu den kritischsten Phasen bei der …”